topblog Ivoire blogs

30/01/2019

Lonsdor K518ISE Read Fiat Freemont Pin Code and Add Smart Key Success

I’ve successfully read pin code and add a smart key to a Fiat Freemont with Lonsdor K518ISE Key Programmer.

(Note: The model is under 90 days free trail. You need to subscribe to use after 3 month.)

Connect K518 Auto Key Programmer host with vehicle via obd socket

Turn ignition to ON position

Select Immobilizer->Fiat->China->Freemont->Smart key->Read Pin Code

lonsdor-k518-fiar-freemont-1

lonsdor-k518-fiar-freemont-2

lonsdor-k518-fiar-freemont-3

Turn ignition off and turn on emergency indicator

lonsdor-k518-fiar-freemont-4

Read 4-digit pin code success.

lonsdor-k518-fiar-freemont-5

Select Add Smart Key

Turn ignition off and turn on emergency indicator

lonsdor-k518-fiar-freemont-6

Keep the smart key need to be registered in car, take other keys outside the car

lonsdor-k518-fiar-freemont-7

Lonsdor K518 will auto fill in pin code read previously

lonsdor-k518-fiar-freemont-8

Press LOCK or UNLOCK button once

lonsdor-k518-fiar-freemont-9

Put the key on the Start button and press UNLOCK button once within 30 seconds.

lonsdor-k518-fiar-freemont-10

Programming completed

lonsdor-k518-fiar-freemont-11

Test the smart key.

It is working.

20/11/2018

wiTECH VCI Pod Vs wiTech MicroPod 2

wiTECH VCI Pod wins wiTech MicroPod 2 in the built-in DRB III emulator ( which is far more stable). wiTech MicroPod two is claimed to work fine with the DRB III emulator, but not contained inside the package you will need to obtain your very own.

For Programming:
Chrysler wiTech MicroPod 2 wins in on line and offline programming etc.
wiTECH VCI Pod wins in crucial programming.

wiTech-MicroPod-2

118.four MB

*** Please use the free source at your own personal danger, nobody will take responsibilities for any danger.

For sake of security, you will be advised to work with the stable a single wiTECH VCI Pod with built-in DRB III emulator or obtain your own 1 to function with the low-cost wiTech MicroPod 2

What is DRB III emulator?
DRB III Emulator may be the exact scan tool application application made use of in Chrysler, Jeep, and Dodge dealerships to service non-CAN primarily based vehicles from 1998-2007. The DRB III Emulator application application now runs on your personal computer and interfaces with our custom DRB III+ hardware device to allow all the functions on the original Chrysler DRB III Scan Tool and much more. This application package even comes with non-powertrain ECU programming files to allow reflashing all the things from BCMs to sliding door modules.

The best way to set up DRBIII Emulator?
For making use of DRBIII Emulator application with tools like VCI pod or Micropod II with witech version 14.xx.xx – 17.xx.xx, it depends upon your device (clone or orig / old or newer release) and ONLY Right after that, set up DRBIII Emulator.

DRBIII-Emulator

Right here a Micropod II user who’re fortunate to obtain the package with DRBIII Emulator, and he shared his productive expertise on how to set up DRBIII Emulator.
1: Get started having a fresh install of Windows 7 Pro 32-bit.
2: Install all of the important drivers for your laptop.
three: Set the clock to the current date and time. (It didn’t perform when set to 01/01/2017)
4: Connect to WiFi and performed all necessary Windows Updates.
5: Copy the “wiTECH_Install_17.03.01” folder to the desktop.
6: Install the supplied version Adobe AIR.
7: Set up the offered version of Java.
eight: Install wiTECH 17.03.01.
9: Following you have got finished installed every thing, whenever you get popup messages from Windows Firewall to allow or block any applications, click “Allow”.
ten: After you get a popup for AdobeAIR and Java to update, click cancel and usually do not update either AdobeAIR or Java.
11: Open “My Computer” and inside the upper left of the window, click on “Organize” and after that select “Folder and search options”.
12: Click around the “View” tab and beneath “Hidden files and folders” pick the radio button for “Show hidden files, folders and drives”. Also, uncheck the choice for “Hide protected operating program files (Suggested)” and after that in the leading with the window, click the “Apply to Folders” button.
13: Navigate to “C:ProgramDatawiTECHjserverdatacorestubs” and you’ll uncover three installers.
14: Set up the DRBIII Emulator stub.
15: Wait for a popup to appear that states the security certificate isn’t valid and click “OK” to let the software update to proceed. Another popup will seem and the software update will run. Following it completes, close the wiTECH window if it opens.
16: Set up the Enhanced DRBIII emulator stub.
17: Again, wait to get a popup to appear that states the security certificate is not valid and click “OK” to allow the application update to proceed. A further popup will seem along with the computer software update will run. After it completes, close the wiTECH window if it opens.
18: Install the K-Line stub.
19: Once more, wait for a popup to seem that states the safety certificate isn’t valid and click “OK” to enable the computer software update to proceed. Another popup will appear and also the application update will run. Immediately after it completes, close the wiTECH window if it opens.
20: Connect the MicroPod2 towards the vehicle, then connect it to the pc.
21: A popup window will seem to set up computer software. Click “OK”.
22: After it finishes, start wiTECH 17.03.01 and wait for the screen to show up with the MicroPod2 and IP address of it. You will see a “Launch DRBIII” button within the lower ideal corner. Ignore it as they don’t adequately open the emulator.
23: Produce a shortcut on the desktop and enter the following in to the ‘Path” field.
24: Disable the LAN and WLAN network connections and in no way connect to the web once more.
25: Click around the shortcut and you’re set! The Auto Scan Tool DRBIII emulator will open and give you the decision to choose various diverse cars.

More……

VCI Pod + DRB III Emulator Logging and Wireshark dump

12/11/2018

Registration and Activation Guide for Lonsdor JLR-IMMO Hardware OBD Key Programmer

Lonsdor JLR-IMMO is a dedicated IMMO device for Jaguar and LandRover, launched by Shenzhen Lonsdor technology company. It’s designed to program car keys and applicable to above 95% of Jaguar and LandRover models currently (VPW protocols of Jaguar’s old model is unsupported). JLR-IMMO supports OBD program mode, and more than 50 software versions for KVM as well. A majority of KVM case is dismantle-free and can be programmed with this device.

New users are required to register, bind and activate the device for the first use. After activation , you can use the device functions.

Users who’ve bound Lonsdor product, can directly enter Email and password to login, no need to register again.
1 Register for website

Please enter the website: http://u.lonsdor.com/jlrimmo/login(see below pic)

Lonsdor-JLR-Key-Programmer-3

Click【Register】, it skips to below interface.

Lonsdor-JLR-Key-Programmer-4

According to prompts in frame box, input related info., click【Submit】to register( see below pic).

Input name: fill in user name

Set password: input min 6-digit login password

Confirm password: reconfirm the login password

Input Email: fill in registered email address

Input verification code: click【Get verification code】, then input the correct code.
Lonsdor-JLR-Key-Programmer-5

2 Website login

After register successful, it skips to login interface.
Or you can enter the website: http://u.lonsdor.com/jlrimmo/login

According to prompts to input Email, password and verification code, click 【Submit】to login.

Lonsdor-JLR-Key-Programmer-6

When login succeeds, it skips to “Bind account” interface.

Lonsdor-JLR-Key-Programmer-7

3 Bind device

According to prompts to input correct info., click【Submit】to bind device.

Device No.: shown on boot screen and back of the device (PSN).

Registration code: after device boot, click A (Enter), there is instruction on activation operation, registration code will show.

Please set device password: 6-digit number

Please confirm Key Programmer password: confirm the password

Lonsdor-JLR-Key-Programmer-8

4 Activate device

Enter website: http://u.lonsdor.com,(see below pic)

Lonsdor-JLR-Key-Programmer-9

Users who’ve bound Lonsdor product before, can directly enter Email and password to login, no need to register on the website. Users who doesn’t bind Lonsdor product, complete website registration, then input the registered Email and password to login.

After login, the screen shows bound device, see below pic.

Lonsdor-JLR-Key-Programmer-10

Click JLR, see below pic.

Lonsdor-JLR-Key-Programmer-11

Click【Get activation code】, the default in input box is bound device No., see below pic.

Lonsdor-JLR-Key-Programmer-12

Click【Submit】, get activation code, see below pic.

Lonsdor-JLR-Key-Programmer-13

Input activation code to the device, press A(Enter), shown in below pic. Press A(Enter) once again, activation succeeds and enter function interface.

Lonsdor-JLR-Key-Programmer-14

www.obd2tool.com