topblog Ivoire blogs

11/02/2018

Autel MaxiSYS Elite No Communication Message

25

If the MaxiSys Display Tablet is not connected to the VCI device, an “Error” message displays. An “Error” message indicates the display tablet is not communicating with the Autel MaxiSYS Elite, and so cannot gain access to the vehicle control module. In this case, you need to do the following check-ups:

1.Check if the VCI device is powered on.
2.In case of wireless connection, check if the network is configured correctly, or if the right device has been paired.
3.If during the diagnosis process, the communication is suddenly interrupted due to the loss of signal, check if there is any object that causes signal interruption.
4.Check if the VCI device is properly positioned. It is recommended to put the VCI device with the front side up.
5.Try standing closer to the VCI device to obtain more stable signals, and faster communication speed.

6.In case of wired connection, check the cable connection between the display tablet and the VCI device.
7.Check if the green LED on the VCI device is illuminated for BT, Ethernet, or USB.
8.Check if the Error LED on the Autel Maxisys device is on, this may indicate there is a communication error between the devices, in this case try re-establishing the connection again; if this does not work, there may be a hardware problem with the device, in this case contact for technical support.

B If the VCI device is unable to establish a communication link, a prompt message displays with check instructions. The following conditions are the possible causes for this massage to display:

1.The Diagnostic Scanner VCI device is unable to establish a communication link with the vehicle.
2.You’ve selected a system for testing that the vehicle is not equipped Incorrect vehicle identification was entered.
3.There is a loose connection
4.There is a blown vehicle fuse.?
5.There is a wiring fault on the vehicle, or the data cable or adapter.
6.There is a circuit fault in the data cable or adapter.
7.Incorrect vehicle identification was entered

10/02/2018

Excel Export of Order Details Tab Data of CAT ET

All Order Details data can be exported in one step to an Excel spreadsheet file

The data of CAT ET from each Order Details tab will be populated on a separate worksheet in one Excel spreadsheet file

Click on the Export Excel button on the Order Details page to export the Order Details data

Excel Export of Order Details Tab Data

14-1 14-2

Order Details –Revoked Licenses Tab Detail

14-3

Order Details – Editable Fields

-> Order Name
-> Purchase Order
-> Organization
-> Attention – Only editable if license is Assigned

Order Details Editable by Dealer Admin
14-4

Order Details Editable by Auto Scanner

14-5

Order Details Attention
* – Editable by Dealer Admin
* License must be Assigned

14-6
14-7
14-8

09/02/2018

How to adjust odometer on Peugeot BSI 2004 HO5 with OBDSTAR X300DP X300 PRO3

OBDSTAR X300DP and OBDSTAR X300 PRO3 is free update to perform automatic identification, read pincode, read eeprom, write EEPROM, read Flash and Cluster calibration on Peugeot /Citroen/ DS models.

Take Peugeot BSI 2004 HO5 odometer adjustment for example.

1-0

Guide:

1-01

This is Peugeot BSI 2004 HO5 type removed from the car.
1-02

Connect X300 DP / X300 Pro 3 with the VCI box and BSI box.

1-03

Tab “Cluster Calibrate”, then “Peugeot”.

1-04

Tab the latest version.

1-05

Warning! Please contact VCI to main unit by USB, to keep stability of vehicle communication.

Tab “OK”

1-06

BSI (cluster calibration)

Option “Auto select” and “Manual select”: If you don’t know what specifi type of BSI, you can tab “Auto select”, if you know the BSI type, tab “Manual select”.

1-07

Tab the third option “JC BSI2004-H0X”

1-08

Switch ignition on

1-09

Next is to operate one by one: Read EEPROM, Mileage adjustment, Write EEPROM, Read Flash.

1-10

Communicating…

Logging in to the system…take 1-2 minutes.

1-11

Reading data…

1-12

Please enter a file name to save.

You should take note this file name.

1-13

Input value:… tab “OK”

1-14

The file name that you enter already exists, whether to cover? tab “Yes”

1-15

Operation succeed.

1-16

Back to tab “Mileage adjustment”

1-17

Has the “Read EEPROM” and “Read Flash” functions been performed? tab “Yes”

1-18

It will take 2-60 mins during testing, keep the vehicle fully charged and don’t unplug OBD connector.

Tab “Yes”.

1-19

Communicating…

1-20

Current mileage: 3000 km

Please confirm the mileage correctly and press ENTER to contine.

Tab “Yes”.

1-21

Please input the mileage of the adjustment.

1-22 1-23

Communicating…

Switch ignition off.

Switch ignition on.

Communicating…

Adjustment success.

1-24
1-25
1-26

Done